|
|
|
|
|
|
Rapid Prep Application Fluid
|
Our Price:
|
|
|
For cleaning or pre-cleaning, Rapid Prep is a non-hazardous wash solvent that removes wax, grease, oil and silicone. After using Rapid Prep to clean the substrate (sign panels, autos or boats) you can apply paint or vinyl. Rapid Prep is also non- flammable, making it a superior product for sign shops, body shops and trim shops where safety is a big concern. Rapid Prep was formulated by people with hands on experience, with a desire to have a safer more effective pre-cleaner.
|
|
|
|
|
|
|
|
|
|
Rapid Clear Application Fluid
|
|
Our Price:
|
|
|
Rapid Clear cleans and polishes plexiglass, glass, and most polycarbonates. Use Rapid Clear as a final cleaning for your sign work, auto restoration, etc. Non-hazardous and bio-degradable.
|
|
|
|
|
|
|
|
|
|
Rapid Tac II Application Fluid
|
|
Our Price:
|
|
|
New Rapid Tac II will enable you to perform wet applications with a wider variety of film types (Intermediate, Cast, Economy, Calendared, Metallic, Reflective, Polyester, Mylar).
Rapid Tac II will also give you better control, allowing vinyl to bond faster to glass, and in cold weather (down to approximately 25 degrees f.)
|
|
|
|
|
|
|
|
|
|
Rapid Remover Application Fluid
|
|
Our Price:
|
|
|
This environmentally friendly product is great for removing adhesive glue left over by decals and vinyl graphics. Rapid Remover is a non-toxic, water-soluble that breaks down and removes adhesives in sixty seconds! You spray it on, wait thirty to sixty seconds, and easily wipe it off with a plastic squeegee, with no damage to painted or bare metal surfaces. What may have been a four-hour job (and a messy one at that) can now be done in one and half-hours: an easy, clean and non-damaging removal. Your shop or business will benefit greatly from these products; think of them as tools. Get the right tool for the job!
|
|
|
|
|
|
|
|
|
|
Rapid Tac Application Fluid
|
|
Our Price:
|
|
|
This environmentally friendly product is great for installing decals and vinyl graphics.
Granted, not all applications call for a "wet" procedure, but we do know that in most applications, forty to sixty percent labor time can be saved by using an application fluid. Sometimes one person can do a job (normally requiring two people to apply dry) in less time if an application fluid like Rapid Tac or new Rapid Tac II is used. (Rapid Tac II bonds faster than Rapid Tac, and is intended for films with a lower tac adhesive than premium vinyl.)
|
|
|
|
|
|
|
|
|
|
WEBERmade Application Tools
|
|
Our Price:
|
|
|
Once you get your tape tool clamped or bolted to your table or work bench, you simply pull your application tape out, over and just past the end of your vinyl. You can adjust the tension of your tape coming off the roll with a quick turn of the tensioning knob. Once you get your tape out and over your vinyl, you simply fasten the application tape to your table and squeegee it down back towards the roll of application tape. The tension that you set with the clutch keeps your application tape up and off your vinyl until you squeegee it down. * You can place one or more rolls of tape up to 48'' onto each of the 2 shafts. * The end support mounting brackets when they are fastened to your table are 3 inches wider than the tape tool.
|
|
|
|
|
|
|
|
|
|
Laminator Big Squeegee
|
|
Our Price:
|
|
|
The Laminator is designed for laminating and mounting prints. It will mount cut vinyl if you use a different tool for masking. Several standard sizes are available that are made for use with printers up to 62 inches. The front edge of the laminator is covered with a replaceable felt. This tool is not to be used for masking.
|
|
|
|
|
|
|
|
|
|
Rivet/Dent Big Squeegee
|
|
Our Price:
|
|
|
This tool is used for mounting small graphics and mounting graphics over rivets and irregular surfaces. It will apply application tape to long graphics.
|
|
|
|
|
|
|
|
|
|
Cut Vinyl Big Squeegee
|
|
Our Price:
|
|
|
An all-around tool for masking and mounting cut vinyl. It can also be used for mounting and laminating printed graphics. The standard size for this tool is 26 and 32 inches. Both front and back edges have replaceable felt. The rear edge allows you to mask multiple small pieces.
|
|
|
|
